Hello! Recently, I created this fabulous background using our stencil butters. For fun, I made up a bunch of postcards and mailed them to art friends to see if any of them could guess how I’d created the background. While there were a few elements guessed correctly and some pretty close guesses, no-one actually guessed the correct combination of products or techniques. Today, this post reveals the process and products I used that kept them guessing!
The Crafter’s Workshop provided me with some product to create this project. The opinions I share are solely my own.
I decided to use some dark blue textured drawing paper, TCW926 Bubble Rebound stencil, and delicate surface tape (which is less sticky than painter’s tape and less likely to tear the paper when removing). Now, the real trick with this background technique is to choose an analogous color scheme (colors next to one another on the color wheel) that matches the color of the paper that you are using. Since I chose royal blue paper, I decided to choose three cool colors to match, and white to provide contrast against the darker blue paper. I chose shades that were lighter than the paper in order to have the paper texture show up and be more visible in the end design.
For this technique, you’re going to work with the stencil under the paper. Tape the paper in place over the stencil. For the first step, I chose to work with NeoColor II water soluble, wax pastel crayons. I wanted a water soluble product so that it would react later in the process, as you’ll see. Laying the crayon almost horizontally on the paper, color random patches of each color over the entire paper. Don’t press too hard, or you’ll lose the paper texture, yet press gently enough so that you can see the edges of the stencil’s outlines on the paper, as shown in the image, below. (You might want to try a couple of practice pieces first to get the amount of pressure just right).
Next it was time to apply the stencil butters. Again, I stuck within the same analogous color palette, so I chose to use the TCW9064 Turquoise stencil butter and the TCW9066 Orchid stencil butter. Using a fairly wide palette knife, I applied the orchid stencil butter randomly over the page first, immediately followed with the turquoise stencil butter randomly in other places (yet overlapping here and there so they blend a little). The trick with this technique is not to load the palette knife with too much stencil butter, don’t press hard with the palette knife, and just lightly scrape the palette knife at a 45 degree angle across the top of the paper. The stencil butter will get caught by the stencil cut out areas, showing the shapes and outlines of the stencil. It’s important that you don’t cover the paper completely, you still want to be able to see some of the Neocolor areas through and under the stencil butters in places. This is what gives the background depth and dimension. Do not wait for the stencil butters to dry!
The next step is to use a spritz bottle to add water drops to the top of the entire paper. You want random drops in different sizes scattered across the page, not a shower or a soaking. Think of the drops as adding a new layer of design to the background. Let the water drops sit on top of the butters and paper for 2 minutes. Note: The water will activate the NeoColor II crayons, blending them where the drops have landed.
Lay a dry piece of kitchen paper towel, with the embossed design down, over the stencil butters, and the entire paper. Using your hands horizontally across the paper, very gently pat the paper towel to remove the water drops and impress the paper towel texture into the stencil butters. This creates two levels of texture, one from the water drops (where the stencil butter will lift off the paper when you remove the paper towel), and one from the paper towel embossing impression pressed into the stencil butter.
Your background is now complete. It is also able to be reactivated by any moisture or wet product, so keep that in mind if you want to be able to work over the top of it. You will want to apply a coat of matte or gloss gel medium to seal it. I would use either an old credit card or a silicon catalyst blade/mini scraper to apply the medium, but you’ll have to work fast and light so as not to smear or reactivate the background design! Pro Tip: Get your medium set up on the tool first, and start it on a scrap piece of paper to adjust it before applying it to the actual piece.
If you’d like to watch a super quick fly-by video (56 seconds) of this process with captions, please hop on over to my YouTube Channel @TealHareCreations.
The Crafter’s Workshop Design Team Member
PSSST! I’m really trying to grow my following. Will you please help me by hopping on over and following me on my blog and social media accounts? Thank you so much!
My Website and Blog: Teal Hare Creations
My YouTube Channel: YouTube Channel
My Instagram account: Instagram
My Pinterest Boards: Pinterest
2 thoughts on “Stencil Butter Backgrounds”
Oh my gosh. This is a phenomenally new technique I’ve never seen before! I was a lucky recipient of a postcard and it baffled me to no end. Thank you for sharing the process…finally! The specific description of each step is impeccably written and easy to understand and follow.
Thank you so much! I’m so glad you liked it and were able to learn how it was done. Happy creating!